|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement rope ring for chimneys. Door Seal Rope, 3/4", 1 foot length.
When ordering specify the length in feet. NOTE: Silicone is not included. Rope may be used for door seal or chimney transition box cover seal (each requires a 5-ft section) on a Maxim furnace. Also used on E-Classic 2300 Reaction Chamber door, heat exchanger access cover, and for the Fusion Combustor and insert.
|
Chimney Rain Cap, 6" (see sizing note below), applicable to Central Boiler furnaces: Maxim M250/M255P/M255PE, Classic Edge 350/550 and E-Classic 1450. To be used with Chimney Extension (p/n 6500004). Also consider 6" Chimney Cap (p/n 2900342).
Part number 4082 was replaced by this part number.
NOTE: Central Boiler sizes chimneys by their inside
diameter. A 6" chimney has a 6" inside diameter and an 8"
outside diameter. An 8" chimney has an 8" inside diameter and a
10" outside diameter. A 10" chimney has a 10" inside
diameter and a 12" outside diameter. When ordering a chimney part
for a Central Boiler furnace, be sure to use the Central Boiler designated chimney
size when ordering rather than the actual measurement. For example, when
ordering a chimney cap for a Classic 6048, even though the actual outside
diameter is 10”, order the 8” chimney cap. If you do not know the proper
size for chimney parts, please call first. All returns for incorrectly
ordered parts drop shipped from Central Boiler will incur return shipping and a
20% restocking fee.
|
Attached to the outer casing of a 6" chimney to hold three guy-wires (not included). Recommended for chimneys exceeding the roof by 5' to 13' maximum.
This band is for chimney's with an inner dimension of 6" and a outer dimension of 8".
NOTE: Central Boiler sizes chimneys by their inside diameter. A 6" chimney has a 6" inside diameter and an 8" outside diameter. An 8" chimney has an 8" inside diameter and a 10" outside diameter. A 10" chimney has a 10" inside diameter and a 12" outside diameter. When ordering a chimney part for a Central Boiler furnace, be sure to use the Central Boiler designated chimney size when ordering rather than the actual measurement. For example, when ordering a chimney cap for a Classic 6048, even though the actual outside diameter is 10”, order the 8” chimney cap. If you do not know the proper size for chimney parts, please call first. All returns for incorrectly ordered parts drop shipped from Central Boiler will incur return shipping and a 20% restocking fee.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Chimney Band Clamp Kit, 6", reinforces strength between two sections of 6" chimney.
Note: 6" band clamps are for the Central Boiler 6" chimney which has an inside diameter of 6" and an outside diameter of 8".
|
Chimney Attachment Ring, 6"/8", used with electrical conduit (not included) to reinforce chimney when five or more sections are used. For use on an interior or exterior wall, stabilizes chimney while providing clearance from combustible surface. Use of Chimney Attachment Rings at maximum intervals of 8' is recommended. Must be located directly below Chimney Locking Band (6" p/n 6500011; 8" p/n 10509) to reduce stress on the joint.
|
Replacement chimney box cover assembly for Maxim M250/M255 P models. Order kit 2500054 if chimney box insert, chimney box cover and chimney box shell are needed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement chimney box cover for Maxim 175 models.
|
Replacement chimney box insulation insert for Maxim 250, 255 P & 255 PE models. Order kit 2500054 if chimney box insert, chimney box cover and chimney box shell are needed.
|
New version chimney cap/spark arrestor provides better fit, features a snaplock clamp and screen that is secured with a clamp-on fastener for easy removal.
6" stainless steel spark arrestor chimney cap for chimney sections used on Maxim 175/250/255 P/255 PE models, E-Classic 1450 models, Classic Edge 350/550 models and Forge 1500/3500 models.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Chimney Box Service Kit (part number 4337) includes all insulation pieces for the Maxim 175 chimney transition box.
|
Chimney Box Assembly for M250/M255.
|
|
|
