|
|
|
|
|
|
|
|
|
|
|
|
|
|
Well, 1/2" NPT fitting.
|
Line Voltage Thermostat (120-volt) used to start the fan on forced-air systems.
|
Can be used in conjunction with zone valves, zone pumps and forced-air systems or used to operated 24-volt 3-way zone valves (requires 24-volt transformer).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Used with 24-volt wall thermostat and 24-volt zone valves.
|
Can be used in conjunction with zone valves, zone pumps and forced-air systems or used to operate 24-volt 3-way zone valves (requires 24-volt transformer).
|
Recommended to be used with Pool Aquastat (p/n 191), sold separately. Stainless Steel Well, 1/2" NPT fitting.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Optional thermal actuator (compatible with stainless steel radiant manifold kits) provides individual loop flow control on multi-zoned manifold.
|
Optional thermal actuator (compatible with stainless steel and nickel brass radiant manifold kits) provides individual loop flow control on multi-zoned manifold. This 4-wire actuator also features end switch for activation of a pump.
|
Plug-in Thermostat, 13.5-amp rated, 110-Volt, is for operating fan.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Non-adjustable, immersible, Fixed Aquastat, 175°F, 1/2" MPT fitting.
|
Non-adjustable, immersible, Fixed Aquastat, 190°F, 1/2" MPT fitting
|
For controlling water temperature in pools, spas, etc., Immersable, temperature range of 40-180°F in one-degree differential. With pool or hot tub application, it is recommended to use a stainless steel well (p/n 1248), sold separately.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For 1992 and older Classic outdoor wood furnaces, adjustable from 100-240°F.
|
Adjustable between 110-240°F, immersible, with 1/2" MPT fittings on well (either close on rise or open on rise). Recommended operating setting is between 165-195°F. Can be installed on Classic model furnaces prior to serial number 25151 that were manufactured with a fixed aquastat.
|
Strap-on Aquastat, adjustable from 65-200˚F with 5 to 30-degree differential.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Large, easy-to-read screen allows homeowners to use one thermostat to control up to three stages of heat and two stages of cooling. Fully programmable. Must be installed and wired by a qualified service technician.
|
Replacement actuator for dual fuel burner purchased December 15th, 2015 and later. Only order part number 8200280 as the replacement if you have already installed one of these actuator kits: 2500179(CLDR) or 2500180(CL7260DR).
|
Kit to replace actuator part number 5742 with the current actuator used on dual ready burner kits (part numbers 6833 and 6834) for all Classic furnaces, excluding the CL 7260. Kit contains actuator, burner clamp, sensor switch assembly, 12-1/8" actuator shaft and closeoff plate. If kit 2500179 was previously purchased then the replacement actuator only would be part number 8200280.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Kit to replace actuator part number 5742 with the current actuator used on dual ready burner kits (part numbers 6843 and 6844) for the Classic 7260. Kit contains actuator, burner clamp, sensor switch assembly, 16-5/8" actuator shaft and closeoff plate. If kit 2500180 was previously purchased then the replacement actuator only would be part number 8200280.
|
|
|
